Our Plastering Services
Good plastering is the foundation of a well-finished interior. Whether you are renovating an older property, making good after building work, or preparing surfaces in a new build, the quality of the plaster finish affects the final appearance of everything applied over it — paint, wallpaper, tiles and more.
We offer a full range of interior plastering services across South Wales, carried out by experienced tradespeople who take pride in achieving a flat, smooth result.
Skim Coat (Finish Plaster)
A skim coat is a thin layer of finish plaster applied over an existing surface to create a smooth, flat finish ready for decoration. Skimming is typically carried out over plasterboard, existing plaster that has been PVA'd, or a sand and cement scratch coat. It is one of the most common plastering jobs in domestic properties — often used after a room has been replastered, after boarding out a wall or ceiling, or to refresh surfaces that have become uneven or patchy over time.
The finished thickness of a skim coat is typically 2–3 mm. The material is applied in two thin layers and trowelled to a smooth, flat surface while still wet. Getting the timing right at each stage — applying the second coat at the right consistency and closing the surface at the right time — is where skill and experience make the difference between a good result and a poor one.
Full Plaster (Scratch, Float and Set)
On bare masonry walls where there is no existing plaster, a full plaster system is required. This involves applying a scratch coat (a rougher, thicker base coat that is keyed before it sets), followed by a floating coat to build the surface up to the correct level and flatness, and finally the finish (set) coat to achieve a smooth surface.
Full plastering is more time-consuming than skimming — the base coats need to be applied, keyed and allowed to stiffen before the next coat goes on — but it is necessary where the substrate is bare masonry and on walls where significant levelling or building-out is required.
Board Skimming
Plasterboard — used extensively on both walls and ceilings in new build and renovation work — is finished by skimming with a thin layer of finish plaster. Taped and skimmed plasterboard produces a seamless surface without visible board joins. We fix and skim plasterboard on ceilings and partition walls as part of our plastering service.
Bonding Coat
Where a surface has very low suction — such as dense concrete, painted masonry or areas that have been repaired with polymer-modified products — a bonding coat is required to create the right surface for the finish plaster to adhere to. Bonding plaster is applied in a thicker layer than a skim coat and provides a sound, keyed substrate for the finish.
Patch Repairs and Making Good
Plaster repairs are a common requirement after building work — chasing walls for cables or pipes, fixing damp, making alterations to doorways or windows, or repairing impact damage. We carry out patch repairs to walls and ceilings and work to blend the new plaster with the surrounding surface as closely as possible. On older, textured or sand and cement surfaces, achieving a completely invisible repair is not always possible, but we aim to minimise the visible difference as far as the existing surface allows.
Why Preparation Matters
The quality of a plaster finish depends as much on what happens before the plaster goes on as on the application itself. The surface must be clean, sound and at the right suction. A wall that is too dry and absorbent will draw moisture out of the plaster too quickly, preventing it from curing properly and leading to cracking or adhesion failure. A surface with too little suction can prevent the plaster from bonding correctly.
We assess the substrate before starting and apply the appropriate primer or PVA dilution to bring the suction to the right level. This preparation step is not something we skip — it is a fundamental part of achieving a plaster finish that will last.
What to Expect
Interior plastering is a wet trade and there will be some disruption during the work. Furniture in the room should be removed or covered, and floor coverings should be protected. We take care to protect surrounding areas and clean up on completion of each day's work.
Fresh plaster needs time to dry out before it can be decorated. The drying time depends on the thickness of the coat, the ventilation in the room and the ambient temperature. As a guide, a skim coat is typically ready for decoration within 5–7 days in normal conditions, though full plaster coats may take longer. We advise on this at the time of the job.
Our Process
-
Assessment and Quote
We visit the property, assess the scope of the plastering work required and provide a clear written quote. We advise on any preparatory work that may be needed before we start.
-
Preparation
Surfaces are checked for stability and any loose or failing material is removed. The surface is primed or PVA'd as appropriate to control suction. Beads are fixed at corners and reveals where required.
-
Base Coat (Where Required)
For full plaster work, scratch and floating coats are applied and allowed to cure to the correct state before the finish coat is applied.
-
Finish Coat
The finish plaster is applied in two passes and worked to a smooth, flat surface using a trowel. The closing stage requires careful timing to achieve the best possible result.
-
Clean Up
We clean up at the end of each day and remove all materials and equipment on completion. We advise on drying times and preparation for decoration before leaving.
Areas Served
We provide plastering services across South Wales, covering Caerphilly, Cardiff, Newport, Pontypridd, Barry and the surrounding areas. If you are unsure whether we work in your area, contact us and we will let you know.